Independent buyer of surplus transformers · Texas-wide pickup

Green pad-mounted distribution transformer on a concrete pad

Waco, TX · Pad-Mounted

Sell Pad-Mounted Transformers in Waco, TX

Sell pad-mounted transformers in Waco, Texas. We assess ratings, cabinet condition and removal access before making unit-specific offers after inspection.

  • Direct buyer, not a broker
  • Texas-wide pickup
  • All voltage classes
Photo: Simon-says-elkay / CC BY-SA 4.0

Owners looking to sell pad-mounted transformers in Waco need to document both the electrical equipment and its surroundings. Texas Electrical Transformer Buyers buys surplus and used units for cash. In McLennan County’s manufacturing, distribution and campus environments, including the broader Baylor University setting, cable connections and restricted pad access can shape the practical requirements of a sale.

01

Record Ratings and Cabinet Condition

Pad-mounted distribution transformers commonly use dead-front, tamper-resistant cabinets and sit on concrete pads. Typical equipment falls within the 15 kV class and ranges from 15 to 2,500 kVA, with single-phase or three-phase configurations. Send the actual nameplate ratings rather than assuming the voltage class from appearance. Include cabinet photographs that show doors, hinges, locks and the overall exterior condition clearly.

The compartment arrangement and installed accessories also matter. Identify documented feed configuration, switching equipment and protection features without opening energized compartments. Describe corrosion, impact damage, oil leakage and missing covers. A complete cabinet with readable identification provides a stronger starting point for evaluation than a capacity estimate alone, but purchase interest still depends on inspection of the individual transformer itself.

  • Nameplate
  • Cabinet
  • Switching
  • Leakage
02

Separate Cable Work From Equipment Handling

A pad-mounted transformer cannot be lifted safely while its electrical connections remain attached. Qualified personnel must manage isolation, verification and cable termination work under applicable site procedures. Explain whether primary and secondary cables have already been disconnected, whether elbows remain installed and who controls the outage. Photographs should be taken without entering energized compartments or disturbing the existing electrical installation.

At Waco manufacturing or distribution properties, equipment changes may need to fit around ongoing operations. Tell us whether the transformer supplies active loads or has been bypassed by replacement equipment. Include the intended release sequence and any access restrictions. We use those details to assess the transaction without assuming your facility can interrupt service simply to make surplus equipment available.

  • Isolation
  • Cables
  • Outage
  • Release
03

Check the Pad and Loading Approach

Measure the cabinet and identify its listed weight when available. Show the concrete pad, lifting access and the route to a truck loading position. Fences, bollards and landscaping can limit reach even when a transformer appears accessible from the street. Explain which barriers can be removed and who is responsible for restoring any disturbed surfaces after equipment handling is complete.

Waco’s I-35 logistics context makes loading details relevant, but proximity to a highway does not resolve onsite access. Gate width, pavement condition and available staging space still need review. Submit those details alongside the electrical information. Our cash offers are unit-specific and based on inspection, with cabinet condition, completeness and the actual removal requirements considered before a purchase is agreed.

  • Pad
  • Bollards
  • Gates
  • Staging
FAQ

Common questions

Do bollards have to be removed before evaluation?

Not necessarily. Send photographs showing their spacing, height and position relative to the transformer’s lifting points. We can review the obstruction before removal work begins. If handling requires moving bollards or fencing, responsibility for that work and any restoration should be established as part of the removal plan.

Can I sell a pad-mounted transformer with cables still connected?

You can submit it for preliminary review while it remains connected, provided you own it and can authorize its sale. Purchase planning must account for qualified disconnection and a safe release from service. Do not cut cables or disturb terminations to prepare photographs. Identify the operating status and who will coordinate the electrical work.

Reviewed by the Texas Electrical Transformer Buyers buying desk · Last updated November 13, 2026

Your transformer has value. Let's put a number on it.

Call 614-715-3047 or send the nameplate. We buy the unit, coordinate the rigging and pay on agreed terms.

614-715-3047 Request an offer
Call 614-715-3047